Drag equation

Drag equation

In fluid dynamics, the drag equation is a practical formula used to calculate the force of drag experienced by an object due to movement through a fully enclosing fluid.

The equation is attributed to Lord Rayleigh, who originally used L2 in place of A (with L being some linear dimension). But see Section 7 of Book 2 of Newton's Principia Mathematica; in particular Proposition 37. The force on a moving object due to a fluid is:

F_D\, =\, \tfrac12\, \rho\, v^2\, C_D\, A

where

FD is the force of drag, which is by definition the force component in the direction of the flow velocity,[1]
ρ is the mass density of the fluid, [2]
v is the velocity of the object relative to the fluid,
A is the reference area, and
CD is the drag coefficient — a dimensionless constant related to the object's geometry and taking into account both skin friction and form drag.

The reference area A is typically defined as the area of the orthographic projection of the object on a plane perpendicular to the direction of motion. For non-hollow objects with simple shape, such as a sphere, this is exactly the same as a cross sectional area. For other objects (for instance, a rolling tube or the body of a cyclist), A may be significantly larger than the area of any cross section along any plane perpendicular to the direction of motion. Airfoils use the square of the chord length as the reference area; since airfoil chords are usually defined with a length of 1, the reference area is also 1. Aircraft use the wing area (or rotor-blade area) as the reference area, which makes for an easy comparison to lift. Airships and bodies of revolution use the volumetric coefficient of drag, in which the reference area is the square of the cube root of the airship's volume. Sometimes different reference areas are given for the same object in which case a drag coefficient corresponding to each of these different areas must be given.

For sharp-cornered bluff bodies, like square cylinders and plates held transverse to the flow direction, this equation is applicable with the drag coefficient as a constant value when the Reynolds number is greater than 1000.[3] For smooth bodies, like a circular cylinder, the drag coefficient may vary significantly until Reynolds numbers up to 107 (ten million).[4]

Contents

Discussion

The equation is based on an idealized situation where all of the fluid impinges on the reference area and comes to a complete stop, building up stagnation pressure over the whole area. No real object exactly corresponds to this behavior. CD is the ratio of drag for any real object to that of the ideal object. In practice a rough unstreamlined body (a bluff body) will have a CD around 1, more or less. Smoother objects can have much lower values of CD. The equation is precise — it simply provides the definition of CD (drag coefficient), which varies with the Reynolds number and is found by experiment.

Of particular importance is the u2 dependence on velocity, meaning that fluid drag increases with the square of velocity. When velocity is doubled, for example, not only does the fluid strike with twice the velocity, but twice the mass of fluid strikes per second. Therefore the change of momentum per second is multiplied by four. Force is equivalent to the change of momentum divided by time. This is in contrast with solid-on-solid friction, which generally has very little velocity dependence.

Derivation

The drag equation may be derived to within a multiplicative constant by the method of dimensional analysis. If a moving fluid meets an object, it exerts a force on the object, according to a complicated (and not completely understood) law. We might suppose that the variables involved under some conditions to be the:

  • speed u,
  • fluid density ρ,
  • viscosity ν of the fluid,
  • size of the body, expressed in terms of its frontal area A, and
  • drag force FD.

Using the algorithm of the Buckingham π theorem, one can reduce these five variables to two dimensionless parameters:

Alternatively, one can derive the dimensionless parameters via direct manipulation of the underlying differential equations.

That this is so becomes apparent when the drag force FD is expressed as part of a function of the other variables in the problem:


  f_a(F_D,\, u,\, A,\, \rho,\, \nu)\, =\, 0. \,

This rather odd form of expression is used because it does not assume a one-to-one relationship. Here, fa is some (as-yet-unknown) function that takes five arguments. We note that the right-hand side is zero in any system of units; so it should be possible to express the relationship described by fa in terms of only dimensionless groups.

There are many ways of combining the five arguments of fa to form dimensionless groups, but the Buckingham π theorem states that there will be two such groups. The most appropriate are the Reynolds number, given by


  R_e\, =\, \frac{u\,\sqrt{A}}{\nu}

and the drag coefficient, given by


  C_D\, =\, \frac{F_D}{\frac12\, \rho\, A\, u^2}.

Thus the function of five variables may be replaced by another function of only two variables:


  f_b\left( \frac{F_D}{\frac12\, \rho\, A\, u^2},\, \frac{u\, \sqrt{A}}{\nu} \right)\, =\, 0.

where fb is some function of two arguments. The original law is then reduced to a law involving only these two numbers.

Because the only unknown in the above equation is the drag force FD, it is possible to express it as


  \frac{F_D}{\frac12\, \rho\, A\, u^2}\, =\, f_c\left( \frac{u\, \sqrt{A}}{\nu} \right)

or


  F_D\, =\, \tfrac12\, \rho\, A\, u^2\, f_c(R_e), \,
    and with      C_D\, =\, f_c(R_e).

Thus the force is simply ½ ρ A u2 times some (as-yet-unknown) function fc of the Reynolds number Re — a considerably simpler system than the original five-argument function given above.

Dimensional analysis thus makes a very complex problem (trying to determine the behavior of a function of five variables) a much simpler one: the determination of the drag as a function of only one variable, the Reynolds number.

The analysis also gives other information for free, so to speak. We know that, other things being equal, the drag force will be proportional to the density of the fluid. This kind of information often proves to be extremely valuable, especially in the early stages of a research project.

To empirically determine the Reynolds number dependence, instead of experimenting on huge bodies with fast-flowing fluids (such as real-size airplanes in wind-tunnels), one may just as well experiment on small models with more viscous and higher velocity fluids, because these two systems are similar.

See also

References

  • Batchelor, G.K. (1967). An Introduction to Fluid Dynamics. Cambridge University Press. ISBN 0521663962. 
  • Huntley, H. E. (1967). Dimensional Analysis. Dover. LOC 67-17978. 

Notes

  1. ^ See lift force and vortex induced vibration for a possible force components transverse to the flow direction.
  2. ^ Note that for the Earth's atmosphere, the air density can be found using the barometric formula. Air is 1.293 kg/m3 at 0°C and 1 atmosphere
  3. ^ Drag Force
  4. ^ See Batchelor (1967), p. 341.

Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Drag (physics) — Shape and flow Form drag Skin friction 0% 100% 10% 90% …   Wikipedia

  • Drag coefficient — In fluid dynamics, the drag coefficient (commonly denoted as: cd, cx or cw) is a dimensionless quantity that is used to quantify the drag or resistance of an object in a fluid environment such as air or water. It is used in the drag equation,… …   Wikipedia

  • Drag — Contents 1 In science and technology 2 In arts, performance arts and entertainment 3 Other uses …   Wikipedia

  • Drag count — A drag count is a single unit of drag as defined by aerospace engineers. Drag is generally computed using the equation: Where: ρ is the air density v is the current airspeed Cd is the drag coefficient (a dimensionless constant, usually on the… …   Wikipedia

  • Morison equation — Flow forces according to the Morison equation for a body placed in a harmonic flow, as a function of time. Blue line: drag force; red line: inertia force; black line: total force according to the Morison equation. Note that the inertia force is… …   Wikipedia

  • Parasitic drag — (also called parasite drag) is drag caused by moving a solid object through a fluid. Parasitic drag is made up of many components, the most prominent being form drag. Skin friction and interference drag are also major components of parasitic drag …   Wikipedia

  • Constitutive equation — Many defining equations are in the form of a constitutive equation, since parameters of a property or effect associated matter are characteristic to the substance in question. A large number of other defining equations not specifically… …   Wikipedia

  • Aerodynamic drag — Note This article is currently under renovation, and may, at times, appear disjoint. Please see the [http://en.wikipedia.org/wiki/Talk:Aerodynamic drag Discussion Page] . Introduction Aerodynamic drag refers to the retarding force on moving… …   Wikipedia

  • Lift-to-drag ratio — In aerodynamics, the lift to drag ratio, or L/D ratio ( ell over dee in the US, ell dee in the UK), is the amount of lift generated by a wing or vehicle, divided by the drag it creates by moving through the air. A higher or more favorable L/D… …   Wikipedia

  • Automobile drag coefficient — The drag coefficient is a common metric in automotive design, where designers strive to achieve a low coefficient. Minimizing drag is done to improve fuel efficiency at highway speeds, where aerodynamic effects represent a substantial fraction of …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”