Balanced audio

Balanced audio

Balanced audio is a method of interconnecting audio equipment using impedance-balanced lines. This type of connection is very important in sound recording and production because it allows for the use of long cables while reducing susceptibility to external noise.

Balanced connections use three-conductor connectors, usually the XLR or TRS jack plug. XLR connectors, for instance, are usually used with microphones because of their durable construction, while TRS jack plugs are usually used for mixer inputs and outputs because of their smaller profile.

Applications

Many microphones operate at low voltage levels and some with high output impedance (hi-Z), which makes long microphone cables especially susceptible to electromagnetic interference. Microphone interconnections are therefore a perfect application for a balanced interconnection, which cancels out most of this induced outside noise.

If the power amplifiers of a public address system are located at any distance from the mixing console, it is also normal to use balanced lines for the signal paths from the mixer to these amplifiers. Many other components, such as graphic equalizers and effects units, have balanced inputs and outputs to allow this. In recording and for short cable runs in general, a compromise is necessary between the noise reduction given by balanced lines and the cost introduced by the extra circuitry they require.

Interference reduction

Balanced audio connections use a number of techniques to reduce noise.

A typical balanced cable contains two identical wires, which are twisted together and then wrapped with a third conductor (foil or braid) that acts as a shield.The term "balanced" comes from the method of connecting each wire to identical impedances at source and load. This means that much of the electromagnetic interference will induce an equal noise voltage in each wire. Since the amplifier at the far end measures the difference in voltage between the two signal lines, noise that is identical on both wires is rejected. The noise received in the second, inverted line is applied against the first, upright signal, and cancels it out when the two signals are subtracted.

This differential signal recombination can be implemented with a differential amplifier. A balun may also be used instead of an active differential amplifier device.

The wires are also twisted together, to reduce interference from electromagnetic induction. Twisting makes the loop area between the conductors as small as possible, and ensures that a magnetic field that passes equally through adjacent loops will induce equal but opposite currents, which cancel out.

The separate shield of a balanced audio connection also yields a noise rejection advantage over an unbalanced two-conductor arrangement (such as used in typical home stereos) where the shield must also act as the signal return wire. Any noise currents induced into a balanced audio shield will not therefore be directly modulated onto the signal, whereas in a two-conductor system they will be. This also prevents ground loop problems, by separating the shield/chassis from signal ground.

Differential signalling

Signals are often transmitted over balanced connections using the differential mode, meaning the wires carry signals of opposite polarity to each other (for instance, in an XLR connector, pin 2 carries the signal with normal polarity, and pin 3 carries an inverted version of the same signal).

Despite popular belief, this is not necessary for noise rejection. As long as the impedances are balanced, noise will couple equally into the two wires (and be rejected by a differential amplifier), regardless of the signal that is present on them.cite web
url=http://www.soundcraft.com/extra_product_pages/audio_balancing/index.html
title=Audio Balancing Issues
accessdate=2007-05-24
author=Graham Blyth
work=Professional Audio Learning Zone
publisher=Soundcraft
] [cite book
title = Sound system equipment
accessdate = 2007-05-24
edition = Third edition
year = 2000
publisher = International Electrotechnical Commission
location = Geneva
id = IEC 602689-3:2001
pages = p. 111
chapter = Part 3: Amplifiers
quote = Only the common-mode impedance balance of the driver, line, and receiver play a role in noise or interference rejection. This noise or interference rejection property is independent of the presence of a desired differential signal.
] A simple method of driving a balanced line is to inject the signal into the "hot" wire through a known source impedance, and connect the "cold" wire to ground through an identical impedance. Due to common misconceptions about differential signalling, this is often referred to as a quasi-balanced or impedance-balanced output, though it is, in fact, fully balanced and will reject common-mode interference.

There are some benefits to driving the line with a fully differential output, though:
* The electromagnetic field around a differential line is ideally zero, which reduces crosstalk into adjacent cables.
* Though the signal level would not be changed due to nominal level standardization, the maximum output from the differential drivers is twice as much, giving 6 dB extra headroom. (If the amplifiers are identical, though, their output noise sums to 3 dB more than a single amplifier, decreasing dynamic range.)
* Noise that is correlated between the two amps (from poor power supply rejection, for instance), would be cancelled out.
* At higher frequencies, the output impedance of the output amplifier can change, resulting in a small imbalance. When driven in differential mode by two identical amplifiers, this impedance change will be the same for both lines, and thus cancelled out.
* Differential drivers are also more forgiving of incorrectly wired adapters or equipment that unbalance the signal by shorting pin 2.

Internally balanced audio design

Most professional audio products (recording, public address, etc.) provide differential balanced inputs and outputs, typically via XLR or TRS connectors. However, in most cases, a differential balanced input signal is internally converted to a single-ended signal via transformer or electronic amplifier. After internal processing, the single-ended signal is converted back to a differential balanced signal and fed to an output. A small number of professional audio products have been designed as an entirely differential balanced signal path from input to output; the audio signal never unbalances. This design is achieved by providing identical (mirrored) internal signal paths for both pin 2 and pin 3 signals (AKA "hot" and "cold" audio signals). In critical applications, a 100% differential balanced circuit design can offer better signal integrity by avoiding the extra amplifier stages or transformers required for front-end unbalancing and back-end rebalancing. Fully balanced internal circuitry has been promoted as yielding 3dB better dynamic range. [ [http://www.sweetwater.com/store/detail/m201/ "Grace Design m201" (promotional ad copy)] Sweetwater Sound]

Connectors

While 3-pin XLR connectors are the most common balanced connector, quarter-inch (¼" or 6.35 mm) TRS connectors (tip-ring-sleeve) are also commonly used. Many hybrid jacks are now designed to take either XLR or TRS.

On TRS plugs, the tip is "hot" (positive), the ring is "cold" (negative), and the sleeve is ground (earthed or chassis). If a stereophonic or other binaural signal is plugged into such a jack, one channel (usually the right) will be subtracted from the other (usually the left), leaving an unlistenable L − R (left minus right) signal instead of normal monophonic L + R. Reversing the polarity at any other point in a balanced audio system will also result in this effect at some point when it is later mixed-down with its other channel.

Telephone lines also carry balanced audio, though this is generally now limited to the local loop. It is called this because the two wires form a balanced loop through which both sides of the telephone call travel.

Data lines, including digital audio, are also frequently balanced, normally using AES/EBU (AES3) with XLR connectors for pro audio.Fact|date=June 2007 Eight-channel analog balanced audio connectors like ADAT use DB25 connectors, which can also carry up to 16 digital channels.

Converters

Unbalanced signals can be converted to balanced signals by the use of a balun, often through a DI unit.

If balanced audio must be fed into an unbalanced connection the electronic design used for the balanced output stage must be known. In most cases the negative output can be tied to ground but in certain cases the negative output should be left disconnected. See [http://www.dself.dsl.pipex.com/ampins/balanced/balanced.htm#6 Douglas Self's page] for specific details.

References

See also

* Balanced line
* Differential pair

External links

* [http://www.ukslc.org/Technical_Articles/Sound/Balanced_Lines.html Uk Sound And Lighting Community — Article On Balanced Lines]
* [http://www.prosoundweb.com/install/sac/n27/rick/balout-1.shtml A Simple Implementation of the Impedance Balanced Output]


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • Audio and video connector — Audio connectors and video connectors are electrical connectors for carrying an audio signal or video signal, either in an analog or digital format. Analog A/V connectors often use Shielded cable to inhibit RF interference and noise. Audio Only… …   Wikipedia

  • Audio system measurements — are made for several purposes. Designers take measurements so that they can specify the performance of a piece of equipment. Maintenance engineers make them to ensure equipment is still working to specification, or to ensure that the cumulative… …   Wikipedia

  • Balanced line — In telecommunications and professional audio, a balanced line or balanced signal pair is a transmission line consisting of two conductors of the same type, and equal impedance to ground and other circuits. [Young EC, The Penguin Dictionary of… …   Wikipedia

  • Balanced circuit — See also Balanced line A balanced circuit is a common method of transmitting many types of communication signals between two points on two wires. In a balanced circuit the individual signals on each wire are inverses of each other as referenced… …   Wikipedia

  • Audio signal — An audio signal is a representation of sound waves in a different form. Typically this is an electrical voltage, but it can be magnetic, when recorded onto analogue tape, for example, or as radio waves. An audio signal can be manipulated, stored …   Wikipedia

  • Audio noise measurement — is carried out when assessing the quality of audio equipment, such as is used in recording studios, broadcast studios, and in the home (Hi Fi).Noise in general refers to unwanted sound, often loud, but in audio systems it is the low level hiss or …   Wikipedia

  • Balanced — F/A/V An audio circuit with 3 wires, two which carry signal, and a third which is contected to a ground (grounded). (Sound) A&V A circuit having two sides (conductors) carrying voltages which are symmetrical around a common reference point,… …   Audio and video glossary

  • balanced line — TV Audio cables that have three wires: one for positive, one for negative and one for ground …   Audio and video glossary

  • Clipping (audio) — For shortening of voice snippets due to failures in voice activity detection, see squelch and voice activity detection. The altered peaks and troughs of the sinusoidal waveform displayed on this oscilloscope indicate the signal has been clipped.… …   Wikipedia

  • Klipsch Audio Technologies — Infobox Company company name = Klipsch Audio Technologies company company type = Manufacturing foundation = 1946 as Klipsch and Associates location = Indianapolis, Indiana key people = Paul W. Klipsch, Founder Fred and Judy Klipsch, Owners Paul… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”