Axle counter

Axle counter

An axle counter is a device on a railway that detects the passing of a train in lieu of the more common track circuit. A counting head (or 'detection point') is installed at each end of the section, and as each axle passes a head at the start of the section, a counter increments. As the train passes a similar counting head at the end of the section, that counter decrements. If the net count is evaluated as zero, the section is presumed to be clear for a second train.

This is carried out by safety critical computers called 'evaluators' which are centrally located with the detection points located at the required sites in the field. These detection points are either connected to the evaluator via dedicated copper cable or via a telecommunications transmission system. This allows the detection points to be located significant distances from the evaluator. This is useful when using centralised interlocking equipment but less so when signalling equipment is distributed at the lineside in equipment cabinets.

Advantages

Axle counters are used in places such as wet tunnels, like the Severn Tunnel, where ordinary track circuits are unreliable. Axle counters are also useful where there are uninsulated steel sleepers which prevent the operation of track circuits. Axle counters are also useful on long sections where several intermediate track circuits may be saved.

Experience with axle counters in mainland Europe shows that they regularly achieve up to five times the reliability of track circuits carrying out the same function.Fact|date=April 2007 This has immediate improvement in service reliability as track circuit failure is often the most significant cause of train delay. It also has safety benefits as it reduces the use of degraded modes of operation outside of the control of the signalling system due to failure.

Disadvantages

Axle counters may forget how many axles are in a section for various reasons such as a power failure. A manual override is therefore necessary to reset the system. This manual override introduces the human element which may be unreliable too. An accident occurred in the Severn Tunnel due to improper resetting of the axle counters.

There are three methods of securing the reset and restoration of axle counters into service:

* Co-operative reset requires both the technician and signaller to co-operate to reset and then restore the section into service. This directly manages the cause of the Severn Tunnel accident.

* Preparatory reset uses the internal logic of the axle counter system to enforce that a train must proceed through a reset section at slow speed, by holding its output as 'occupied' until the train is successfully detected as passing through the section. This logically proves the section free of obstruction and therefore allows the section to change its output to 'clear'.

* Conditional reset (with aspect restriction) has the section reset only if the last count was in the outward direction. This at least shows that any trains in the section at time of reset were at least moving out. The signal protecting the reset section is held at danger by signalling logic outside of the axle counter evaluator to enforce a low speed 'sweep' of the section prior to restoration to service.

Most countries use a variation of the above three methods, sometimes with varying amounts of automation or human input.

Broken rails

The track circuit provides additional functionality of detecting many, though not all, kinds of broken rails, though only to a limited extent in AC traction areas and not in the common rail in DC traction areas. Axle counters, however, offer no such facility. However, experience has shown that broken rails often occur near the insulated block joints which are used to electrically isolate adjacent track circuits. Since axle counters do not require such block joints, the risk of having a broken rails is significantly reduced.

Electromagnetic brakes

Magnetic brakes are used on high speed trains (maximum speed greater than 160 kmh). These are physically large pieces of metal mounted on the bogie of the vehicle, only a few centimetres above the track. They can sometimes be mistakenly detected by axle counters as another axle. This can happen only on one side of a track block, because of magnetic field curvature, defects of track geometry, etc., leading the signalling system into confusion and also requiring reset of the detection memory.


Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • Counter — This article is about the term counter used in electronics and computing. For other uses, see Counter (disambiguation). In digital logic and computing, a counter is a device which stores (and sometimes displays) the number of times a particular… …   Wikipedia

  • Railway signalling — Not to be confused with Railway signal. A gantry of British semaphore signals seen from the cab of a steam locomotive Railway signalling is a system used to control railway traffic safely, essentially to prevent trains from colliding. Being… …   Wikipedia

  • Severn Tunnel rail accident — On December 7, 1991, the 08:30 Paddington to Cardiff HST was stopped at a signal guarding the entrance to the Severn Tunnel. On telephoning the signalman, the driver was advised of a signal failure and given permission to proceed at caution.… …   Wikipedia

  • Rail tracks — are used on railways (or railroads), which, together with railroad switches (or points), guide trains without the need for steering. Tracks consist of two parallel steel rails, which are laid upon sleepers (or cross ties) that are embedded in… …   Wikipedia

  • South Central Railway — The South Central Railway is one of the 16 railway zones in India. It is headquartered at Secunderabad and has the following divisions: Reorganized Secunderabad, Hyderabad, Guntakal (including Bellary Guntakal (MG)), Vijayawada, Guntur and Nanded …   Wikipedia

  • Treadle (railway) — In railway signalling, a treadle is a mechanical or electrical device that detects that a train axle has passed a particular location. They are used where a track circuit requires re inforcing with additional information about a train s location …   Wikipedia

  • Continuous Automatic Warning System — For the gun, see Heckler Koch HK CAWS. For the wrestling video game creation mode, see Create a wrestler. The Continuous Automatic Warning System (CAWS) is a form of cab signalling and train protection system used in Ireland to help train drivers …   Wikipedia

  • Track (rail transport) — Permanent way redirects here. For other uses, see Permanent way (disambiguation). Twin rail tracks in a wooded area …   Wikipedia

  • Level crossing — This article is about at grade intersections between railway and road. For where two rail lines cross, see level junction. For a type of nuclear receptor (RXR), see Retinoid X receptor. A level crossing at Chertsey, England, as the barriers rise …   Wikipedia

  • Railway signal — Not to be confused with Railway signalling. A signal is a mechanical or electrical device erected beside a railway line to pass information relating to the state of the line ahead to train/engine drivers. The driver interprets the signal s… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”