Fully differential amplifier

Fully differential amplifier

A fully differential amplifier, usually referred to as an 'FDA' for brevity, is a DC-coupled high-gain electronic voltage amplifier with differential inputs and differential outputs. In its ordinary usage, the output of the FDA is controlled by two feedback paths which, because of the amplifier's high gain, almost completely determines the output voltage for any given input.

The ideal FDA

For any input voltages the "ideal" FDA has infinite open-loop gain, infinite bandwidth, infinite input impedances resulting in zero input currents, infinite slew rate, zero output impedance and zero noise.

A Real FDA can only approximate this ideal, and the actual parameters are subject to drift over time and with changes in temperature, input conditions, etc. Modern integrated FET or MOSFET FDAs approximate more closely to these ideals than bipolar ICs where large signals must be handled at room temperature over a limited bandwidth; input impedance, in particular, is much higher, although the bipolar FDA usually exhibit superior (i.e., lower) input offset drift and noise characteristics.

Where the limitations of real devices can be ignored, an FDA can be viewed as a Black Box with gain; circuit function and parameters are determined by feedback, usually negative. An FDA as implemented in practice is moderately complex integrated circuit

Limitations of real FDAs

DC imperfections

* Finite gain — the effect is most pronounced when the overall design attempts to achieve gain close to the inherent gain of the FDA.
* Finite input resistance — this puts an upper bound on the resistances in the feedback circuit.
* Nonzero output resistance — important for low resistance loads. Except for very small voltage output, power considerations usually come into play first. (Output impedance is inversely proportional to the idle current in the output stage — very low idle current results in very high output impedance.)
* Input bias current — a small amount of current (typically ~10 nA for bipolar FDAs, or picoamperes for CMOS designs) flows into the inputs. This current is mismatched slightly between the inverting and non-inverting inputs (there is an input offset current). This effect is usually important only for very low power circuits.
* Input offset voltage — the FDA will produce an output even when the input pins are at exactly the same voltage. For circuits which require precise DC operation, this effect must be compensated for.
* Common mode gain — A perfect operational amplifier amplifies only the voltage difference between its two inputs, completely rejecting all voltages that are common to both. However, the differential input stage of an FDA is never perfect, leading to the amplification of these identical voltages to some degree. The standard measure of this defect is called the common-mode rejection ratio (denoted, CMRR). Minimization of common mode gain is usually important in non-inverting amplifiers (described below) that operate at high amplification.
* Temperature effects — all parameters change with temperature. Temperature drift of the input offset voltage is especially important.

AC imperfections

* Finite bandwidth — all amplifiers have a finite bandwidth. This is because FDAs use internal frequency compensation to increase the phase margin.
* Input capacitance — most important for high frequency operation because it further reduces the open loop bandwidth of the amplifier.
* Common mode gain — See DC imperfections, above.
* Noise - all real electronic components (except superconductor) generate noise. You can find devices with 0.8 to several hundreds nv/rtHz noise performance.

Nonlinear imperfections

* Saturation — output voltage is limited to a peak value, usually slightly less than the power supply voltage. Saturation occurs when the differential input voltage is too high for the op-amp's gain, driving the output level to that peak value.
* Slewing — the amplifier's output voltage reaches its maximum rate of change. Measured as the slew rate, it is usually specified in volts per microsecond. When slewing occurs, further increases in the input signal have no effect on the rate of change of the output. Slewing is usually caused by internal capacitances in the amplifier, especially those used to implement its frequency compensation, particularly using pole splitting.
* Non-linear transfer function — The output voltage may not be accurately proportional to the difference between the input voltages. It is commonly called distortion when the input signal is a waveform. This effect will be very small in a practical circuit if substantial negative feedback is used.

Power considerations

* Limited output power — if high power output is desired, an op-amp specifically designed for that purpose must be used. Most op-amps are designed for low power operation and are typically only able to drive output resistances down to 2 kΩ.
* Limited output current — the output current must obviously be finite. In practice, most op-amps are designed to limit the output current so as not to exceed a specified level thus protecting the FDA and associated circuitry from damage.

DC behavior

Open-loop gain is defined as the amplification from input to output without any feedback applied. For most practical calculations, the open-loop gain is assumed to be infinite; in reality it is obviously not. Typical devices exhibit open-loop DC gain ranging from 100,000 to over 1 million; this is sufficiently large for circuit gain to be determined almost entirely by the amount of negative feedback used. Op-amps have performance limits that the designer must keep in mind and sometimes work around. In particular, instability is possible in a DC amplifier if AC aspects are neglected.

AC behavior

The FDA gain calculated at DC does not apply at higher frequencies. To a first approximation, the gain of a typical FDA is inversely proportional to frequency. This means that an FDA is characterized by its gain-bandwidth product. For example, an FDA with a gain bandwidth product of 1 MHz would have a gain of 5 at 200 kHz, and a gain of 1 at 1 MHz. This low-pass characteristic is introduced deliberately, because it tends to stabilize the circuit by introducing a dominant pole. This is known as frequency compensation.

Typical low cost, a general purpose FDA exhibits a gain bandwidth product of a few megahertz. Specialty and high speed FDAs can achieve gain bandwidth products of hundreds of megahertz. Some FDAs are even capable of gain bandwidth products greater than a gigahertz.

See also

* Operational amplifier applications
* Instrumentation amplifier
* Active filter
* Analog computer
* Current-feedback operational amplifier
* Operational transconductance amplifier

External links

* [http://focus.ti.com/lit/an/sloa054d/sloa054d.pdf Fully-Differential Amplifiers] ( TI Application Report)
* [http://www.ti.com/sc/docs/apps/msp/journal/aug2000/aug_08.pdf Fully Differential Amplifiers] (TI Analog Applications Journal)


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Differential amplifier — symbol The inverting and non inverting inputs are distinguished by − and + symbols (respectively) placed in the amplifier triangle. Vs+ and Vs− are the power supply voltages; they are often omitted from the diagram for simplicity, but of course… …   Wikipedia

  • Electronic amplifier — A practical amplifier circuit An electronic amplifier is a device for increasing the power of a signal. It does this by taking energy from a power supply and controlling the output to match the input signal shape but with a larger amplitude. In… …   Wikipedia

  • Operational amplifier — A Signetics μa741 operational amplifier, one of the most successful op amps. An operational amplifier ( op amp ) is a DC coupled high gain electronic voltage amplifier with a differential input and, usually, a single ended output.[1] An op amp… …   Wikipedia

  • Valve audio amplifier - technical — Circuitry and performance Characteristics of valves Valves are very high input impedance (near infinite in most circuits) and high output impedance devices. They are also high voltage / low current devices.While valves themselves are described… …   Wikipedia

  • Virtual ground — In the theory of electrical networks, a virtual ground ( or virtual earth) is a node of the circuit that is maintained at a steady reference potential, without being connected directly to the reference potential. In some cases the reference… …   Wikipedia

  • State variable topology — refers to filters with two pole filter topology. State variable filters are available in lowpass, highpass, bandpass, and notch versions. The notch version is not recommended, because it requires too many amplifiers. It is one of three topologies …   Wikipedia

  • Balanced audio — is a method of interconnecting audio equipment using impedance balanced lines. This type of connection is very important in sound recording and production because it allows for the use of long cables while reducing susceptibility to external… …   Wikipedia

  • Adel Sedra — is an Egyptian electrical engineer whose research specialization is microelectronics, with particular emphasis on applications in communication and instrumentation systems. He received his bachelor of science in electrical engineering from Cairo… …   Wikipedia

  • Mixed-signal integrated circuit — A mixed signal integrated circuit is any integrated circuit that has both analog circuits and digital circuits on a single semiconductor die. [1] [2] [3] Contents 1 Examples 2 …   Wikipedia

  • Pioneer SX-1980 — The Pioneer SX 1980 was a receiver that Pioneer Electronics Corporation introduced in 1978, to be matched with the HPM series of speakers. It is rated at a staggering 270 watts per channel into 8 ohms. [http://www.silverpioneer.netfirms.com/sx… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”