Marine propulsion

Marine propulsion
A view of a ship's engine room

Marine propulsion is the mechanism or system used to generate thrust to move a ship or boat across water. While paddles and sails are still used on some smaller boats, most modern ships are propelled by mechanical systems consisting a motor or engine turning a propeller, or less frequently, in jet drives, an impeller. Marine engineering is the discipline concerned with the design of marine propulsion systems.

Steam engines were the first mechanical engines used in marine propulsion, but have mostly been replaced by two-stroke or four-stroke diesel engines, outboard motors, and gas turbine engines on faster ships. Nuclear reactors producing steam are used to propel warships and icebreakers, and there have been attempts to utilize them to power commercial vessels. Electric motors have been used on submarines and electric boats and have been proposed for energy-efficient propulsion.[1]

Contents

Power sources

Pre-mechanisation

A wind propelled fishing boat in Mozambique

Until the application of the steam engine to ships in the early 19th century, oars propelled galleys, or the wind propelled sailing ships. Before mechanisation, merchant ships always used sail, but as long as naval warfare depended on ships closing to ram or to fight hand-to-hand, galleys dominated in marine conflicts because of their maneuverability and speed. The Greek navies that fought in the Peloponnesian War used triremes, as did the Romans at the Battle of Actium. The use of large numbers of cannon from the 16th century meant that maneuverability took second place to broadside weight; this led to the dominance of the sail-powered warship.

In modern times, human propulsion is found mainly on small boats or as auxiliary propulsion on sailboats. Human propulsion includes the pole, still widely used in marshy areas, rowing which was used even on large galleys, and the pedals.

Propulsion by sail generally consists of a sail hoisted on an erect mast, supported by stays and spars and controlled by ropes. Sail systems were the dominant form of propulsion until the nineteenth century. They are now generally used for recreation and racing, although experimental sail systems, such as the kites/royals, turbosails, rotorsails, wingsails, windmills and SkySails's own kite buoy-system have been used on larger modern vessels for fuel savings.

Reciprocating steam engines

SS Ukkopekka uses a triple expansion steam engine

The development of piston-engined steamships was a complex process. Early steamships were fueled by wood, later ones by coal or fuel oil. Early ships used stern or side paddle wheels, while later ones used screw propellers.

The first commercial success accrued to Robert Fulton's North River Steamboat (often called Clermont) in the US in 1807, followed in Europe by the 45-foot Comet of 1812. Steam propulsion progressed considerably over the rest of the 19th century. Notable developments included the steam surface condenser, which eliminated the use of sea water in the ship's boilers. This permitted higher steam pressures, and thus the use of higher efficiency multiple expansion (compound) engines. As the means of transmitting the engine's power, paddle wheels gave way to more efficient screw propellers.

Steam turbines

The NS Savannah was the first nuclear-powered cargo-passenger ship

Steam turbines were fueled by coal or, later, fuel oil or nuclear power. The marine steam turbine developed by Sir Charles Algernon Parsons raised the power-to-weight ratio. He achieved publicity by demonstrating it unofficially in the 100-foot Turbinia at the Spithead Naval Review in 1897. This facilitated a generation of high-speed liners in the first half of the 20th century, and rendered the reciprocating steam engine obsolete; first in warships, and later in merchant vessels.

In the early 20th century, heavy fuel oil came into more general use and began to replace coal as the fuel of choice in steamships. Its great advantages were convenience, reduced manpower by removal of the need for trimmers and stokers, and reduced space needed for fuel bunkers.

In the second half of the 20th century, rising fuel costs almost led to the demise of the steam turbine. Most new ships since around 1960 have been built with diesel engines. The last major passenger ship built with steam turbines was the Fairsky, launched in 1984. Similarly, many steam ships were re-engined to improve fuel efficiency. One high profile example was the 1968 built Queen Elizabeth 2 which had her steam turbines replaced with a diesel-electric propulsion plant in 1986.

Most new-build ships with steam turbines are specialist vessels such as nuclear-powered vessels, and certain merchant vessels (notably Liquefied Natural Gas (LNG) and coal carriers) where the cargo can be used as bunker fuel.

LNG carriers

New LNG carriers (a high growth area of shipping) continue to be built with steam turbines. The natural gas is stored in a liquid state in cryogenic vessels aboard these ships, and a small amount of 'boil off' gas is needed to maintain the pressure and temperature inside the vessels within operating limits. The 'boil off' gas provides the fuel for the ship's boilers, which provide steam for the turbines, the simplest way to deal with the gas. Technology to operate internal combustion engines (modified marine two-stroke diesel engines) on this gas has improved, however, so such engines are starting to appear in LNG carriers; with their greater thermal efficiency, less gas is burnt. Developments have also been made in the process of re-liquefying 'boil off' gas, letting it be returned to the cryogenic tanks. The financial returns on LNG are potentially greater than the cost of the marine-grade fuel oil burnt in conventional diesel engines, so the re-liquefaction process is starting to be used on diesel engine propelled LNG carriers. Another factor driving the change from turbines to diesel engines for LNG carriers is the shortage of steam turbine qualified seagoing engineers. With the lack of turbine powered ships in other shipping sectors, and the rapid rise in size of the worldwide LNG fleet, not enough have been trained to meet the demand. It may be that the days are numbered for marine steam turbine propulsion systems, even though all but sixteen of the orders for new LNG carriers at the end of 2004 were for steam turbine propelled ships.[2]

Nuclear-powered steam turbines

In these vessels, the nuclear reactor heats water to create steam to drive the turbines. Due to low prices of diesel oil, nuclear propulsion is rare except in some Navy and specialist vessels such as icebreakers. In large aircraft carriers, the space formerly used for ship's bunkerage could be used instead to bunker aviation fuel. In submarines, the ability to run submerged at high speed and in relative quiet for long periods holds obvious advantages. A few cruisers have also employed nuclear power; as of 2006, the only ones remaining in service are the Russian Kirov class. An example of a non-military ship with nuclear marine propulsion is the Arktika class icebreaker with 75,000 shaft horsepower (55,930 kW). Commercial experiments such as the NS Savannah have so far proved uneconomical compared with conventional propulsion.

In recent times, there is some renewed interest in commercial nuclear shipping. Nuclear powered cargo ships could lower costs associated with carbon dioxide emissions and travel at higher cruise speeds than conventional diesel powered vessels.[3]

Reciprocating diesel engines

A modern diesel engine aboard a cargo ship

Most modern ships utilise a reciprocating diesel engine as their prime mover, due to their operating simplicity, robustness and fuel economy compared to most other prime mover mechanisms. The rotating crankshaft can be directly coupled to the propeller with slow speed engines, via a reduction gearbox for medium and high speed engines, or via an alternator and electric motor in diesel-electric vessels.

The reciprocating marine diesel engine first came into use in 1903 when the diesel electric rivertanker Vandal was put in service by Branobel. Diesel engines soon offered greater efficiency than the steam turbine, but for many years had an inferior power-to-space ratio. The advent of turbocharging however hastened their adoption, by permitting greater power densities.

Diesel engines today are broadly classified according to

  • Their operating cycle: two-stroke engine or four-stroke engine
  • Their construction: crosshead, trunk, or opposed piston
  • Their speed
    • Slow speed: any engine with a maximum operating speed up to 300 revolutions per minute (rpm), although most large two-stroke slow speed diesel engines operate below 120 rpm. Some very long stroke engines have a maximum speed of around 80 rpm. The largest, most powerful engines in the world are slow speed, two stroke, crosshead diesels.
    • Medium speed: any engine with a maximum operating speed in the range 300-900 rpm. Many modern four-stroke medium speed diesel engines have a maximum operating speed of around 500 rpm.
    • High speed: any engine with a maximum operating speed above 900 rpm.

Most modern larger merchant ships use either slow speed, two stroke, crosshead engines, or medium speed, four stroke, trunk engines. Some smaller vessels may use high speed diesel engines.

The size of the different types of engines is an important factor in selecting what will be installed in a new ship. Slow speed two-stroke engines are much taller, but the footprint required, is smaller than that needed for equivalently rated four-stroke medium speed diesel engines. As space above the waterline is at a premium in passenger ships and ferries (especially ones with a car deck), these ships tend to use multiple medium speed engines resulting in a longer, lower engine room than that needed for two-stroke diesel engines. Multiple engine installations also give redundancy in the event of mechanical failure of one or more engines, and the potential for greater efficiency over a wider range of operating conditions.

As modern ships' propellers are at their most efficient at the operating speed of most slow speed diesel engines, ships with these engines do not generally need gearboxes. Usually such propulsion systems consist of either one or two propeller shafts each with its own direct drive engine. Ships propelled by medium or high speed diesel engines may have one or two (sometimes more) propellers, commonly with one or more engines driving each propeller shaft through a gearbox. Where more than one engine is geared to a single shaft, each engine will most likely drive through a clutch, allowing engines not being used to be disconnected from the gearbox while others keep running. This arrangement lets maintenance be carried out while under way, even far from port.

Gas turbines

Combined
marine
propulsion

CODOG
CODAG
CODLAG
CODAD
COSAG
COGOG
COGAG
COGAS
CONAS

Many warships built since the 1960s have used gas turbines for propulsion, as have a few passenger ships, like the jetfoil. Gas turbines are commonly used in combination with other types of engine. Most recently, the Queen Mary 2 has had gas turbines installed in addition to diesel engines. Because of their poor thermal efficiency at low power (cruising) output, it is common for ships using them to have diesel engines for cruising, with gas turbines reserved for when higher speeds are needed however, in the case of passenger ships the main reason for installing gas turbines has been to allow a reduction of emissions in sensitive environmental areas or while in port.[4] Some warships, and a few modern cruise ships have also used the steam turbines to improve the efficiency of their gas turbines in a combined cycle, where wasted heat from a gas turbine exhaust is utilized to boil water and create steam for driving a steam turbine. In such combined cycles, thermal efficiency can be the same or slightly greater than that of diesel engines alone; however, the grade of fuel needed for these gas turbines is far more costly than that needed for the diesel engines, so the running costs are still higher.

Screws

The technical term for what is often described as a "propeller" on a ship is a screw. The differentiation is necessary as the two systems, although similar in appearance, have very different physical properties. There are many variations of marine screw systems, including twin, contra-rotating, controllable-pitch, and nozzle-style screws. Smaller vessels tend to have a single screw. Some modern aircraft carriers use four propellers, supplemented with bow- and stern-thrusters. Power is transmitted from the engine to the screw by way of a propeller shaft, which may or may not be connected to a gearbox.

Paddle wheels

Left: original paddle wheel from a paddle steamer.
Right: detail of a paddle steamer.

The paddle wheel is a large wheel, generally built of a steel framework, upon the outer edge of which are fitted numerous paddle blades (called floats or buckets). The bottom quarter or so of the wheel travels underwater. Rotation of the paddle wheel produces thrust, forward or backward as required. More advanced paddle wheel designs have featured feathering methods that keep each paddle blade oriented closer to vertical while it is in the water; this increases efficiency. The upper part of a paddle wheel is normally enclosed in a paddlebox to minimise splashing.

Sailing

The purpose of sails is to use wind energy to propel the vessel, sled, board, vehicle or rotor.

References


Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Nuclear marine propulsion — is propulsion of a ship by a nuclear reactor. Naval nuclear propulsion is propulsion that specifically refers to naval warships (see Nuclear navy). Only a very few experimental civil nuclear ships have been built; the elimination of fossil fuel… …   Wikipedia

  • Marine fuel management — (MFM) is a multi level approach to measuring, monitoring, and reporting fuel usage on a boat or ship, with the goals of reducing fuel usage, increasing operational efficiency, and improving fleet management oversight. MFM has grown in importance… …   Wikipedia

  • Marine engineering — refers to the engineering of boats, ships, oil rigs and any other marine vessel. It can refer to: The engineering of vessel s propulsion systems, see Marine propulsion The engineering of structures to support vessels, see Marine architecture A… …   Wikipedia

  • Propulsion — may refer to:* Vehicle propulsionMore specifically: * Ground propulsion * Marine propulsion * Air propulsion * Spacecraft propulsion …   Wikipedia

  • Marine Engineering and Research Institute — (MERI/DMET), Calcutta Established August 1949 Type Autonomous research and training institute Principal (Director in charge) M. K. Ghosh, C. Eng …   Wikipedia

  • Marine steam engine — Period cut away diagram of a triple expansion steam engine installation, circa 1918 A marine steam engine is a reciprocating steam engine that is used to power a ship or boat. Steam turbines and diesel engines largely replaced reciprocating steam …   Wikipedia

  • Marine automobile engine — Volkswagen Marine 3.0 litre V6 TDI 265 6 marine engine. This is a marine modified version of Volkswagen Groups 3.0 V6 24v TDI CR automobile engine. Marine automobile engines are types of automobile petrol or diesel engines that have been… …   Wikipedia

  • Marine engine — A marine engine is an engine that propels a ship or boat. Types of marine engine include: Marine steam engine Petrol engine or gasoline engine Diesel engine Steam turbine Gas turbine See also Marine propulsion Engine room Marine automobile engine …   Wikipedia

  • Marine Soviétique — La marine de guerre soviétique (Военно морской флот СССР, Voyenno morskoy flot SSSR, littéralement « Forces militaires navales de l URSS ») fut, à son apogée, la deuxième puissance militaire maritime du globe (1 742 navires de… …   Wikipédia en Français

  • Marine sovietique — Marine soviétique La marine de guerre soviétique (Военно морской флот СССР, Voyenno morskoy flot SSSR, littéralement « Forces militaires navales de l URSS ») fut, à son apogée, la deuxième puissance militaire maritime du globe… …   Wikipédia en Français

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”